Third-Party Inspection Agency · Bangladesh
DUPRO Production Inspection and Investigation in Bangladesh
We offer During Production Inspection (DUPRO), an on-site quality control service performed while your goods are actively being manufactured. It typically happens once 10% to 80% of the order is completed, allowing the buyer to catch and fix manufacturing flaws before the entire batch is ruined.
- Specs, samples and AQL from you
- Visit at 10%–20% produced
- Root-cause investigation
- Approved raw materials in useVERIFIED
- Workmanship vs reference sampleACTION NEEDED
- Measurements vs specificationWITHIN AQL
- Daily output vs ship dateON SCHEDULE
How it works
Hire Us as Your Third-Party DUPRO Inspection Company
The buyer can hire us as a third-party inspection company (or assign their own QA team) and provide their product specifications, reference samples, and Acceptance Quality Limit (AQL) standards. We act as the inspection agency and schedule a visit with the factory once at least 10%–20% of the units are produced.
Why buyers book DUPRO
What Our DUPRO Means for Buyers' Orders
Three things change for your order when an inspector is on the factory floor while production is running.
Early Intervention
Instead of waiting until the end of production to discover a mistake, our DUPRO acts as an early warning system on the factory floor.
Specification Verification
We ensure the factory follows your exact design, uses approved raw materials, and maintains consistent quality across the production line.
Schedule Monitoring
Our inspectors check the factory’s daily output rate to confirm your supplier will finish on time.
Production investigation
DUPRO Production Investigation: From Defect to Root Cause
Finding a defect is half the job. When a DUPRO shows a problem, our inspectors investigate where it starts, so the factory fixes the cause and not only the faulty units.
Sectors we inspect
DUPRO Production Inspection by Industry
Each industry fails in different places. Our checklist for every DUPRO starts from your specification and the risks that are typical for your product.
Contract Pharmaceuticals, Nutraceuticals & Medical Disposables
For contract-made health products, DUPRO focuses on what can be checked on the packing line and against the buyer’s specification.
- Lot number, expiry date and label artwork on samples
- Fill count, fill weight and blister or seal integrity
- Dimensions and pack seal condition of medical disposables
- Carton, shipper marking and packing-area housekeeping
A DUPRO does not replace regulatory GMP inspections or laboratory testing.
Home Textiles and Terry Products
Towels, bed linen and other home textiles are checked for weight, size and finish before the full order is woven, cut and sewn.
- Fabric weight (GSM) and finished size after hemming
- Pile density, pulled loops and weaving faults on terry
- Shade against the approved sample and between batches
- Hem and selvedge stitching, labels, folding and packing
Ready-Made Garments (RMG) — Deepening the Core
RMG is Bangladesh’s core export. A mid-run check keeps size, sewing quality and shade consistent across lines and colours.
- Measurements against the size specification
- Stitches per inch, seam puckering and open seams
- Shade variation between panels, bundles and lots
- Trims, accessories, labels and end-of-line reject levels
Leather and Leather Goods
Bags, wallets, belts and other leather goods are checked for material grade, workmanship and fittings while production is still running.
- Leather grade, grain defects and colour consistency
- Edge painting, stitching and lining finish
- Zips, buckles and metal fittings work smoothly
- Signs of moisture or mould before packing
Consumer Electronics Assembly, Cables & Electrical Accessories
For assembled electronics and electrical accessories, samples are checked for function, marking and build quality against your specification.
- Function check on sample units
- Cable length, conductor and insulation condition
- Plug, pin and connector dimensions
- Rating labels and required marks are present and correct
Electrical safety tests are run on the factory’s equipment where agreed.
Ceramics and Tableware
Ceramic defects come from forming, glazing and firing. A DUPRO finds them while the kiln schedule can still be adjusted.
- Glaze defects such as pinholes, crawling and specks
- Chips, cracks, warpage and wobble
- Size, capacity and set completeness
- Decoration and decal position, and protective packing
Plastics, Packaging, and Household Goods
Moulded and packaging products repeat the same fault on every cycle until the cause is fixed, so early checks protect the whole run.
- Flash, short shots, sink marks and warpage
- Wall thickness, weight, colour and lid fit
- Print quality and registration on packaging
- Carton condition and stacking of finished goods
Need a DUPRO for Another Product?
Send us your specification, reference sample and AQL. We will prepare a checklist for your product. To see the inspection by other product groups, read our during production inspection page.
Your choice
Third-Party Inspection or Your Own QA Team?
Both can run a DUPRO with your specifications, reference samples and AQL. The difference is independence, coverage and cost of having people on the factory floor.
Hire us as a third-party inspector
Independent of the factory
- Inspector has no commercial tie to the supplier
- Same checklist and AQL on every visit
- No travel or local staff needed in Bangladesh
- Root-cause investigation and follow-up included in the plan
Assign your own QA team
Works when you already have staff on the ground
- Your team knows your product history
- Needs people in Bangladesh or regular travel
- Harder to cover several factories at once
- We can still provide checklists or extra inspectors
FAQs
DUPRO Production Inspection and Investigation FAQs
What is DUPRO production inspection and investigation?
It is an on-site check of your goods while they are being made (the DUPRO production inspection), followed by an investigation of any repeated defect to find its root cause on the production line, so the factory can fix it before the order is finished.
What is a DUPRO inspection?
A DUPRO (During Production Inspection) is an on-site quality control check made while goods are being manufactured, typically once 10% to 80% of the order is complete. It lets the buyer catch and fix manufacturing flaws before the whole batch is finished.
When do you schedule a DUPRO visit?
We schedule the visit with the factory once at least 10%–20% of the units are produced, so there is enough output to sample and enough time left to correct problems.
Why hire a third-party DUPRO inspection company?
A third-party inspector is independent of the factory, applies the same checklist and AQL every time, and gives you eyes on the factory floor in Bangladesh without sending your own staff.
Can my own QA team do the DUPRO instead?
Yes. Buyers can assign their own QA team. We can also support your team with checklists or extra inspectors when you have several factories or tight dates.
What do I need to provide before the inspection?
Your product specifications, reference samples, Acceptance Quality Limit (AQL) standards, the factory address and the planned production dates.
What does production investigation mean?
When the inspection finds repeated defects, we trace them to the line, operation, machine or material lot that causes them, and agree a corrective action with the factory.
How do you check whether the factory will ship on time?
Our inspectors check the factory’s daily output rate and compare it with the quantity left and your shipping date.
Which industries do you inspect in Bangladesh?
Contract pharmaceuticals and medical disposables, home textiles and terry, ready-made garments, leather goods, consumer electronics and electrical accessories, ceramics and tableware, and plastics, packaging and household goods.
Book a DUPRO Before Your Order Is Finished
Send your specifications, reference samples and AQL. We will confirm the checklist and schedule the factory visit once 10%–20% of the units are produced.
